1991 Magerle MGC-80.32.45 — UMS record #14570
Grinders, Creep Feed, CNC
Historical UMS record #14570
Specifications
CAPACITY
Table Length36 "
Table Width14 "
X-Axis (Longitudinal) Travel31.52 "
Y-Axis (Cross) Travel12.6 "
Z-Axis Vertical) Travel17.73 "
Max. Distance Between Table & Grinding Spindle25.61 "
WHEEL
Max. Diameter15.76 (19.7) "
Max. Width3.94 (6.3) "
Bore (Hole)5 (7.998) "
Circumferential Speed Of Grinding Wheel1378 (2362.2) In/Sec
MOTORS
Main Spindle Motor100 HP.
STROKE SPEED
X-Axis (Longitudinal) Travel1181 IPM
Y-Axis (Cross) Travel118.1 IPM
Z-Axis (Vertical) Travel98.425 IPM
ROTARY TABLE
ManufacturerFibro
Type3-Axis N/C Combo
Tilt Range+15/-2 Degrees
Diameter Of Table Top W/O T-Slots13.4"
Table Size17.3" x 13.4"
Tilt Range+55/-0 Degrees
Table Diameter6.3"
Tilt+10/-10 Degrees
Equipped With
Special 3-Axis NC Table Combination Consisting Of:
"A-Axis Table"
Model:NC2.03.0340.1.1.14.14
With 340mm (13.4") Diameter Table Top Without T-Slots
With Hydraulic Clamping
With Mounted AC Servo Motor Including 1000 Line Count Encoder
With Sheetmetal Covers Over Motor
Motor Mounted To Rear Of Housing Over 2:1 Gearbelt
Table With Alignment Slot
Table With Air Purge
4-Fold Row Limit Switch For Direction Detection Reference & Over Travel Limits
"A-Axis Trunnion":
Model: NC2.03.0320.1.1.00.00
Table Alignment Slot
Table With Manifold Thru Center Of Tble For 8 Hydraulic & Pneumatic Lines & 11 Elec Cables
"A-Axis Cradle":
Special Casting Mounting To A-Axis Table & Trunnion
"B-Axis Table":
Model: NC1.03.0000.0.1.14.10
-With Special 440mm x 340mm (17.3" x 13.4") Table Top
-With Hydraulic Clamping
-With Mounted AC Servo Motor Including 1000 Line Encoder
-With Sheetmetal Covers Over Motor
-Motor Mounted To Rear Of Housing Over 2:1 Gearbelt
-Table With Alignment Slot
-Table With Air Purge
-4-Fold Row Limit Switch For Direction Detection Reference & Over Travel Limits
-Table With 6-Line Manifold For Hydraulic & Pneumatic Supply To "B" Axis
"C-Axis Table":
Model: NC2.01.0160.1.1.14.10
Tilt +10/-10 Degrees
-Special Base Plate Designed As Manifold To SupplyPower To B-Axis
-160mm (6.3") DiameterTable Top Without T-Slots
-With Provision To Pull 2 Electrical Cables Through Center Of Table
-Motor Mounted Over 2:1 Gearbelt To Underside Of Housing
-Table With OverTravel & Direction Detection Switches
"C-Axis Trunnion":
Special Design
-Hydraulic Clamping
-With 4-Line Hydraulic Manifold Through Center Of Table
-With Alignment Slot
-With Air Purge
"C-Axis Cradle":
Special Design & Mounted to "C" Axis & Trunnion
**** New Cost For This Table - $360,450.00****
Fanuc 150M/Crt CNC Control
RS-232 Interface
Flood Coolant System
CNC Wheel Dresser
7-Axis (X,Y,Z,A,B,C, & Dresser)
NEW COST
Owner Paid $968,000.00 in 1991 for Machine & Rotary Table